Digital Data Communications FCS-4200 Manuale Utente

LevelOne FCS-4000 / FCS-4100 / FCS-4200 FCS-4300 / FCS-4400 / FCS-4500 Day/Night P/T/Z IP Speed Dome Camera User Manual

Camera installation  Before installation, please set for the communication protocol, baud rate and camera ID address first

 Protocol setup The dip-switchers are for protocol setup. Please set it up as below: No.5 is ON. *Remarks: Please reboot the camera after th

 You can also follow the triangle in front of camera and aim at the bottom screw to fixing.  After the camera is installed, please turn the c

Hook up the safety buckle, and screw the two screws to fix the power box.  CAS-4000B ceiling mount kit Fixed the iron tu

The assembly completed.  CAS-4000D pole mount kit Fixed the bracket on the rear of power box. The assemb

Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to t

Upon IP CamLocator’s start up, this program searches for LevelOne’s products on the same LAN. After searching, LevelOne Video Servers or Network ca

complete installation. Custom Setup Type: You may install the system to the directory of your preference and choose which feature(s) you w

How to Use IP CamLocator This chapter introduces how to monitor the image from the camera using IP CamLocator. The LevelOne video server and Network

Main Menu Camera Click this button to get into common information of all Network cameras in network. You can connect the specific Network cameras to

Before You Use This Product The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performanc

seeking from 192.168.0.2, to 192.168.0.254. If any of the address inside this range is free, the Network Video server will be assigned to this IP ad

Account settings: The account setting is displayed. You can change the account setting here. Press “Next” to continue, “Previous” to go back, “

Date/Time settings: You can set the date/time of the network camera here. See ”Hint” for details. Press “Next” to continue, “Previous” to go back,

Network settings: You can change the network settings of the network camera here. See “Hint” for details. Press “Next” to continue, “Previous” to

PPPoE settings: You can change the PPPoE settings here. See “Hint” for details. Press “Next” to continue, “Previous” to go back, “Cancel” to go to

DDNS settings: You can change the DDNS settings here. Press “Next” to continue, “Previous” to go back, “Cancel” to go to the main page.

Apply settings: Click on “Apply” to use the new settings. Choose “Reboot system to apply new (network) settings” to reboot after the settings are

Upgrade Choose a network camera, click on Upgrade to upgrade the firmware. You have to key in the username and password of the administrator to en

Factory Default Choose a network camera, click on Factory default to reset the configurations to default. You have to key in the user name and pa

Reboot Choose a network camera, click on Reboot to reboot the device. You have to key in the user name and password to use the reboot function. C

ATTENTION 1. All operation please refer to the instruction. 2. Please don’t place the product on unstable desk or bracket. 3. Please avoid any liq

User The System page provides you all Network Cameras configurations in the network with product or downloaded configuration file information, inclu

From PC File：Click it and press Load to select configuration location from PC. Note: • Configuration file format is *.conf.

From Device：Click it and press Load to select the specific device in the network. Type the Username and Password to load configuration from device.

After loading, you can get configuration from PC files or devices. IP CamLocator displays the sub folders including Info, User, Date Time, TCP/IP, P

User The Network Camera default account and password setting is “root/MAC address of IP camera (in capital letters)”. IP CamLocator provides to assi

Date/Time Current date & time：This displays the current date and time of the camera. PC clock：This displays the date and time of the monitoring

TCP/IP HTTP Port：Select port 80 in general situations. If you want to use a port number other than 80, select the text box and enter a port number

Secondary DNS：Enter the IP address of the secondary DNS server, if necessary.

PPPoE Use this when you connect the camera through PPPoE (Point -to- Point Protocol over Ethernet). PPPoE connection is the protocol that is widely

DDNS Server Name：Select the DDNS Server User ID：Enter the user ID for authentication necessary for DDNS connections. Type it up to 64 characters.

Table of Contents Before You Use This Product... 2 Package Conte

About This page displays IP CamLocator information including Version, Copyright and Product Date information Note： • This computer procedure is prot

How to Access to the Network Camera This chapter introduces how to monitor the image from the camera using Microsoft web browser. The LevelOne video

Configuration of Main Console Language You can click the pulldown box to select system language, including English, Traditional Chinese, German, D

Video Buffer: Turn the Video Buffer function On/Off. The Video Buffer function makes the streaming more smoothly in unsteady network environment, b

Pan / Tilt control Click the arrow button of the direction you want the IP camera to move. Note: This function is only for PTZ Cameras. You can

Live View Snapshot: You can capture a still image shot by the camera and save it in your computer. Press , and a snapshot window will appear. Cl

camera(s) via the Ethernet using your microphone. Video play buttons: ：Pause the current video ：Play the video. ：Stop the current video.

Basic Setting Click the “Basic” folder to display the sub folders, including System, Camera, Network, and Account. System Information The Informati

Day & Time Current date & time：This displays the current date and time of the device. PC clock：This displays the date and time of the moni

Reboot：Click this button to reboot the device. A confirmation dialogue will appear. Click OK to proceed. It takes about two minutes to reboot the d

Package Contents  FCS-4000/FCS-4100/FCS-4200/FCS-4300/FCS-4400/FCS-4500  Power Adapter  Power & A/V Cable  LAN Cable  Alarm Cable  CD Man

Camera General RTSP: Switch the RTSP streaming On/Off. Note： • RTSP: Real Time Streaming Protocol. RTSP is supported by most of the media client

MPEG4 Computer View MPEG4 viewer port (If RTSP mode is OFF) Unicast streaming Video/Audio port number : Specify the transmission port number of the

RTSP (If RTSP mode is ON) RTSP port: Specify the transmission port number of RTSP streaming video. Default value is 554. Viewer authentication: If

unit “fps” stands for “frames sent per second”. Quality Auto：The quality and bitrate will be automatically decided according to the frame rate. Fix

11000. Specify an even number from 1024 to 65534. Time-To-Live: Set the maximum TTL that multicast can pass through. Image Size: The Image size of

MJPEG Note： • MJPEG settings are unavailable if the RTSP mode is ON, which means the MJPEG streaming is closed. MJPEG viewer port Unicast streamin

Network Information MAC address：Display the MAC address of the device. Obtain an IP address automatically (DHCP)：If a DHCP server is installed on t

follows: Example: when HTTP port number is set to 2000 Æ http://192.168.1.100:2000/

PPPoE Use this when you connect the device through PPPoE (Point -to- Point Protocol over Ethernet). PPPoE connection is the protocol that is widely

DDNS Server name：Choose the DDNS Server from the list. User ID：Enter the user ID for authentication necessary for DDNS connections. Type it up to

 Focusing control: Users can press the zoom button to adjust the image viewing distance.  Iris control The factory default is auto iris, ensurin

UPnP The device includes support for UPnP, which is enabled by default. If also enabled on your computer, the device will automatically be detected

IP Notification When network notify type is set to On, you can send an e-mail notification of the completion of the network setting. Notify type：

Type the text of the E-mail up to 384 characters. Default value provides network information including IP, Port, MAC, Model, Firmware Version and We

Security Account The device default account and password setting is “root/MAC address of IP camera (in capital letters)”. That means everyone might

HTTPS HTTPS is a URI scheme used to indicate a secure HTTP connection. It is syntactically identical to the http:// scheme normally used for accessi

62Advance PTZ Control In this section, it provides Pan, Tilt, Zoom, Focus, Iris and Auto Pan speed control setting saved, as well as the Protocol, B

63Preset Position In this section, up to 32 Pan / Tilt and Zoom positions can be saved, as well as the home position, which the camera faces to when

preset position setting.

Patrol There are four patrol tours to set for composing different preset positions. Each one lists up to 8 positions which can be programmed, and th

3. Click the SET. The tour position is saved. 4. Follow the steps to set the other orders. 5. Click the OK to save the tour.

Hardware Installation Installation Notice Please be sure to follow all the steps of the instructions. Wrong installation may damage the product. FCS

FTP Client Use this menu to set up for capturing and sending images to an FTP server. By using FTP client function, you can send the image and audio

Set to forward the image and audio file to the specified FTP server linked with the alarm detection by the external sensor input or by the built-in

Periodical sending You can set to send an image file to FTP server periodically by selecting On to send the image file to FTP server linked with se

SMTP Set the SMTP menu when you want to send an image via e-mail. By using Mail (SMTP) function, you can send a mail with attached image which has b

followings. SMTP: Select if SMTP authentication is necessary when an e-mail is sent. POP before SMTP: Select if POP before SMTP authentication is n

Alarm sending Set to send the mail with connection to the alarm detection by the external sensor input or by the built-in motion detection function.

the Alarm Buffer — Alarm buffer setting Menu on page.

Periodical sending You can set to send an image file by SMTP server periodically by selecting On to send the image file by SMTP server linked with s

sensor input or with the built-in motion detection function to HTTP server. HTTP client setting menu is composed of two tabs, General and Alarm send

Alarm sending Set to send the mail with connection to the alarm detection by the external sensor input or by the built-in motion detection function.

 Finally cover up the smoked cover to accomplish the installation. Please be sure hands are clean while cover up, or it may dirty the cover. It’s

Schedule When you click Schedule on the Advanced mode menu, the Schedule setting menu appears. This is the same menu as the setting menu which is di

78Alarm Input When you click Alarm Input on the Advance mode menu, the Alarm output setting menu appears. You can set in this menu to control the

Alarm Buffer You can set the Pre-alarm image and audio (the image and audio before the alarm detection) and the Post - alarm image and audio. These

Motion Detection When you click Motion Detection on the Advance mode menu, the Motion Detection setting menu appears. There are three Motion Detecti

A detecting zone 1 appears and use mouse to adjust and move the zone boundaries and position. Use tool bar to set Threshold and Sensitivity value. F

System Log The System Log function allows users to review any changes and events happened. The system starts logging automatically after started. Re

83 Trouble shooting sheet Troubles Probable Reasons Solutions Wrong power cable connection. Reverse. The power adapter broken. Change. Fuse bro

84Technical Parameters Model FCS-4000/4300 FCS-4100/4400 FCS-4200/4500 Compression Mode MJEG/MPEG4 Max. Resolution 704x480 pixels(NTSC) 704x576 pix

85GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston,

86Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will ind

 unscrew the bottom screw to install cables.  Insert the plug, and pull these cables through out from the bot

87c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the

88compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is nor

89It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such clai

90 NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW